Plumbing Basics – This Is How Your Home Plumbing System Works


You may not realize it, but water is the most complicated flow in your home. While electricity and people flow through our homes within seconds, water is the most complicated flow of all. Candu Plumbing of Chatsworth announced homes are built with plumbing systems that have been developed over the past century by engineers and experts. Without the proper knowledge, these systems may seem complicated or even impossible to understand.

Water supply

The plumbing system in your home includes two basic systems: the water supply and the drain-waste vent. The water supply delivers clean water to your house, and the drain-waste-vent system carries dirty water to sewers or septic tanks. Natural-gas plumbing provides fuel for gas-burning appliances. The water supply routes clean water from the street to your home, and branches off to supply hot and cold water to different fixtures.

The water supply is provided by the city, and runs along a metal or plastic supply line to each fixture. The supply lines are connected by shut-off valves, which are located near the water meter outside the home.


Your home’s drainage system, also called the drain-waste-vent (DWV) system, is comprised of fat pipes that carry wastewater from the sink and toilet to the sewer or septic tank. These pipes use gravity to carry the waste water out, while vent pipes allow air to enter the system to allow the waste to flow freely.

The drainpipes are made of cast iron, galvanized steel, copper, or plastic. The materials vary by region, but most older homes are made from a combination of different materials. The sink drain will typically have a p-trap, a trap that collects water that prevents sewer gases from entering the home. The drainpipe will then be attached to the p-trap.

Bridge fixtures

Bridge fixtures are the points where the supply and drainage systems of your home meet. They draw fresh water into the home and drain wastewater. Some fixtures even have individual shutoff valves. Ideally, they should be one-piece construction and only have one connection, such as a faucet or sink.

The bridge faucet is a traditional fixture, and the bridge design dates back to Victorian times, when indoor plumbing was still an uncommon luxury. The pipe-like base makes it easy to adjust the temperature and makes it easy to clean around the faucet. Its low-profile design makes it an excellent choice for both bathrooms and kitchens.


Valves in your home plumbing system regulate the flow of pressurized water. There are several different types. Depending on the location of your fixtures, you may need a straight or angled valve. A plumbing service in Jacksonville, Florida, can assist you in installing the right valves. In addition, they offer a range of plumbing solutions, including water heaters.

The most common type of valve found in plumbing systems is the gate valve. This type of valve is typically operated with a knob that raises and lowers a metal gate inside the valve body. It can reduce or completely shut off the flow of water.


When you are planning to remodel your home’s plumbing system, you must understand the role of fittings. These accessories are necessary to connect pipes of different sizes. For example, a valve fitting is used to shut off the water, usually under a sink or in the main water line. Another type of fitting is an adapter fitting, which converts one type of pipe into another. You can also choose an elbow fitting if you want to change the direction of a pipe.

Another important type of fitting is compression fitting, which is a great alternative to soldering. This type of fitting is able to handle high water pressure without popping off. These fittings have a threaded nut and body and are usually made of brass or plastic. However, they may be made of other materials as well.

Water flow

If you notice that some faucets do not seem to be getting the proper water flow, it may be time to have a plumbing professional check the system. If the water flow is not as good as it once was, there may be a clogged pipe or a leak somewhere. To check for leaks, turn off the water supply and check the water meter.

Your home plumbing Chatsworth system is made up of two parts: one that brings fresh water into your house and another that removes wastewater. The water coming into your home travels under pressure and passes through a meter that will register how much water you use. Often, there is a main shut-off valve near the meter.

If there is an emergency, you should always close this shut-off valve to ensure that the water doesn’t go anywhere.

Candu Plumbing of Chatsworth
9726 Variel Ave, Chatsworth, CA 91311
(818) 492-3067

Similar Posts